11 RC-2000 Thermostat Installation Instructions DESCRIPTION The RC-2000 is a precision digital thermostat designed for 24 VAC he
1100 Heat Pump (2 Stage Heat / 1 Stage Cool) 24VAC Common*24VAC "HOT"Auxilirary HeatCompressorGround FaultHumidifierFanDehumidierCompressor
1111 Two Speed Heat Pump (3 Stage Heat / 2 Stage Cool) Comp Stage 2 RelayComp Stage 1 RelayCompressor Stage 2954138671112(D)(H)(L)(G)(Y1)(B)(O)(W2)(C
1122 REMOTE SYSTEM WIRING DIAGRAMS This thermostat has been preprogrammed with energy saving program schedules. When used with a remote system, HAI
1133 HAI HOME CONTROL SYSTEMS The thermostat can be connected to an HAI Home Control system. The controller can send commands to the thermostat to c
1144 REMOTE SETBACK SWITCH The thermostat can be connected to a remote switch to toggle the desired heat and cool temperature settings between preset
1155 REMOTE TEMPERATURE SENSOR A remote temperature sensor can be installed to monitor the temperature from a remote location or can be combined with
1166 DISABLE LOCAL CONTROL The Task Buttons and Scroll Wheel on the thermostat can be disabled to prevent anyone from controlling the thermostat loca
1177 SETUP AND CONFIGURATION NOTE: For proper operation of the features of this thermostat, the Time and Date must be set. Even when connected
1188 System Options Note: Before operating the thermostat, the “System Type” and “System Mode” must be configured. The thermostat can be configured
1199 Cool/Heat Min On/Off These items are used to limit the on and off times of the cooling and heating system (in minutes). Cool Minimum On The n
22 Location When replacing an existing thermostat, install the RC-2000 in the same location. If the existing location doesn't meet the followin
2200 EEC Control The EEC Settings are used to configure Energy Efficient Control, 2nd Stage Differential, and Auxiliary Heat Differential. Not all o
2211 Anticipator Control The Anticipator Control settings are used to “anticipate” the need to turn the system on or off before the temperature is a
2222 Temperature Sensors The Temperature Sensor settings are used to configure the internal temperature sensor and optional remote temperature sensor
2233 Emergency Heat Options The Emergency Heat Options are used to reconfigure the H (Humidifier) or D (Dehumidifier) outputs on the RC-2000 to activ
2244 TROUBLESHOOTING TIPS SYMPTOM ACTION TO TAKE Thermostat Dead 1. Check power to the thermostat 2. Check wiring diagrams SYMPTOM ACTION TO
33 Connect each wire to the terminal strip(s) on the thermostat base per the wiring diagram for your system application - See Figures 4 - 10. Form t
44 TYPICAL WIRING DIAGRAMS CAUTION: Do not short gas valve, fan, heat relay, or cool relay...even momentarily. Do not attempt to h
55 3. When configured as a conventional thermostat, by default this thermostat does not turn the fan on with a call for heat. If the furnace requir
66 Single Stage Conventional 24VAC "HOT"Heat24VAC Common*FanCoolHumidifierDehumidierUP24VACCONTROLTRANSMFOMERDehumidifierHumidifierFan Rela
77 Single Stage Conventional for Zone Control Systems (W2)4(Y2)(D)(H)(G)(Y1)(W1)(C)(RC)10138671112ZONE CONTROLLERTHERMOSTATDehumidifierHumidifierSyst
88 Two Stage Conventional (2 Stage Heat / 2 Stage Cool) UPHeat 1Heat 224VAC Common*24VAC "HOT"DehumidierHumidifierCool 2Cool 1Fan24VACCONTR
99 About Heat Pump Systems 1) Terminal 5 (O) is energized for cooling Terminal 6 (B) is energized for heating In most applications, the reversing
Komentarze do niniejszej Instrukcji